Terminal Server ETS Family
- ET8PS
- ETS16PS
- ETS16PR
- ETS32PR

Advanced Security SecureBox®
- SDS1101
- SDS1100
- SDS2100

Commercial
- EDS8/16/32
- EDS4100
- UBox®
- UDS1100
- UDS2100
- UDS-10 NEW
- UDS10/ 100-IAP
- UDS200
- MSS100
- MSS4
- MSS485-T
- CoBox-FL

Industrial
- IntelliBox®-I/O NEW
- UDS1100-IAP
- UDS-10-IAP
- UDS100-IAP
- XPress-I/O NEW
- XPress-DR+™
- XPress-DR+ Wireless
- XPress-DR™
- XPress-DR-IAP
- CoBox-FL-IAP

External Device Servers

UDS-10

Highlights

• Replace expensive dedicated PCs with fast and reliable networking technology
• Compact size enables it to fit almost anywhere
• Supports RS-232, RS-422 and RS-485 serial connections
• 10Mbps or 10/100Mbps Ethernet through an RJ45 connector
• Configure via HTTP, DHCP, Telnet or serial
• Flash ROM for easy upgrades

Remotely Monitor, Manage and Share
Connected Devices Over a Network of the Internet

In today’s economy, faster and better access to information can mean the difference between success and failure. The UDS-10 single-port device server provide a quick, simple and cost-effective way to bring the advantages of data accessibility and remote management to equipment not currently connected to a network.

Commercial Device NetworkingOur approach to network-enabling devices is transparent to your attached devices and software. So, you won’t need to change the way you work, and there’s no need to develop special software to take advantage of Ethernet networking. And with the UDS-10 any piece of equipment with a serial port can be added to the network in a matter of minutes!

Using a method called serial tunneling, the UDS-10 encapsulates serial data into packets and transports it over Ethernet. Using two UDS-10s, connected by a network, virtual serial connections can be extended across a facility or around the world. So you can manage your equipment from virtually anywhere over Ethernet or the Internet.

The included redirection software extends the functionality of your COM port-based Windows® applications. With virtual COM ports, mapped to remote device servers on the network, you can replace direct serial connections.
Easy to Set Up and Use

The included Windows-based configuration software simplifies installation and setup. The UDS-10 can also be set up locally through its serial port, or remotely over a network using Telnet or a web browser.

The UDS-10 even includes a built-in web server, which can be used for configuration, or to display operating and troubleshooting information on the attached links to online support.

Flash memory provides for maintenance-free nonvolatile storage of web pages, and allows future system software upgrades.
Modem Replacement

In modem emulation mode, the UDS-10 is used to replace dial-up modems. The unit accepts modem AT commands on the serial port, then establishes a network connection to the end device, leveraging network connections and bandwidth to eliminate dedicated modems and phone lines. If you’re looking for a transparent, cost-effective, and scalable means to network-enable your serial devices, look no further than the UDS-10.

back to toptop of page
Features / Specifications
Protocols Supported
ARP, UDP, TCP, Telnet, ICMP, SNMP, DHCP, TFTP and HTTP
Device Support
Supports any asynchronous serial device with 7 or 8-bit data,with or without parity requiring Ethernet access
Network Interface
RJ45 (10Base-T or 10Base-T/100Base-TX) Ethernet
Serial Interface
DB25F, RS-232/RS-422/RS-485 serial port with DCE configuration
Data Rates
Serial speeds 300 bps to 115Kbps
Model Controls
RTS, CTS, DSR, DCD, DTR
Flow Control

* Software XON/XOFF
* Hardware CTS/RTS

Management

* Internal HTTP server
* SNMP (read only)
* Serial login
* Telnet login

Firmware
Flash ROM standard; downloadable from a TCP/IP host (TFTP) or over the serial port
LED

* Good link (green)
* Network transmit/receive data (yellow)
* Collisions (red)
* Diagnostic (red)
* Status (green)

Power Requirements
Power input via standard barrel connector or DB25 serial connector
Input Range 9 to 30 VDC or 9 to 24 VAC @ 250mA
Environmental
Operating 5° to 50° C (41° to 122° F)
Storage -40° to 66° C (-40° to 151° F)
Packaging
Dimensions (HxWxD) 0.9 x 2.5 x 3.5 in (2.3 x 6.4 x 9.0 cm)
Weight .8 lbs (.35 Kg)
Shipping Dimensions
Dimensions (HxWxD) 4.5 x 9.5 x 7.5 in (11.5 x 24.2 x 19.1 cm)
Weight 3.0 lbs (1.5 Kg)
Agency Approvals
CE, FCC B, TUV, C/UL
 

Or Call: 1.800.663.1141 now and speak to one of our sales associates.